Post by stinsonpilot on Jan 30, 2012 0:40:57 GMT -5
Researched communications issues in biplanes and the CEP style headset is by far my favorite. ( www.cep-usa.com/id38.htm )
Only problem is they're a little pricey for what they are. (about $180)
I flew a Sonerai II Midwing for awhile, N93ST and still have a high regard for them. I keep in touch with the community through the forums. I now fly a Steen Skybolt but remember that my Sonerai was as noisy as my open pit 200hp Skybolt with the same hearing protection and communications issues because of the noise.
I thought I would pass this information to you guys.
I made these and put them in my HGU-33 Helmet, but they work for headsets just as well.
Since they are connected to the speaker in the helmet/headset, your helmet/headset speaker still works with or without the ear buds plugged in.
This is my version and it works very well. (not to mention way cheaper)
Components:
1) Skullcandy Ink'd Ear Buds: Because the cord comes straight out the back without the 90 degree support that most have. Headsets tend to pull those type out of your ear. About $11 for a set. I shortened them by overlapping the cord and heat shrink. Guess you could cut and reconnect.
2) Comply Memory Foam ear plugs: These are the same plugs used by CEP on theirs. These are the T-400 Model specifically made for the above Skullcandy ear buds. $16 for a set of three. Should last at least a flying season if not more.
3) 1/8th" Stereo Jack from Radio Shack: This goes in the helmet as the receptacle for the headphone plug. About $3.50 for a set of two.
4) 100 Ohm Resistor: This is to reduce the volume on the ear buds. Aviation speakers are typically 300 to 500 Ohm speakers. The Skullcandy ear buds are way lower and therefore very loud. About $1.75 for 5 at Radio Shack. You could use a higher Resistor to lower the volume further, or you could find a way to put a volume control inline.
I soldered the 100 Ohm Resistor across the left and right channels on the 1/8" Stereo jack to make it mono for the intercom/radio.
This works very well and way cheaper than the CEP set up.
The only other thing I might change is to find a 90 degree adapter so the plug doesn't stick out so far from the helmet, not really a problem in my airplane.
I may have forgotten something, feel free to ask questions, suggestions welcome as well.
Hope this helps. 37 years in aviation I've lost enough of my hearing.
Only problem is they're a little pricey for what they are. (about $180)
I flew a Sonerai II Midwing for awhile, N93ST and still have a high regard for them. I keep in touch with the community through the forums. I now fly a Steen Skybolt but remember that my Sonerai was as noisy as my open pit 200hp Skybolt with the same hearing protection and communications issues because of the noise.
I thought I would pass this information to you guys.
I made these and put them in my HGU-33 Helmet, but they work for headsets just as well.
Since they are connected to the speaker in the helmet/headset, your helmet/headset speaker still works with or without the ear buds plugged in.
This is my version and it works very well. (not to mention way cheaper)
Components:
1) Skullcandy Ink'd Ear Buds: Because the cord comes straight out the back without the 90 degree support that most have. Headsets tend to pull those type out of your ear. About $11 for a set. I shortened them by overlapping the cord and heat shrink. Guess you could cut and reconnect.
2) Comply Memory Foam ear plugs: These are the same plugs used by CEP on theirs. These are the T-400 Model specifically made for the above Skullcandy ear buds. $16 for a set of three. Should last at least a flying season if not more.
3) 1/8th" Stereo Jack from Radio Shack: This goes in the helmet as the receptacle for the headphone plug. About $3.50 for a set of two.
4) 100 Ohm Resistor: This is to reduce the volume on the ear buds. Aviation speakers are typically 300 to 500 Ohm speakers. The Skullcandy ear buds are way lower and therefore very loud. About $1.75 for 5 at Radio Shack. You could use a higher Resistor to lower the volume further, or you could find a way to put a volume control inline.
I soldered the 100 Ohm Resistor across the left and right channels on the 1/8" Stereo jack to make it mono for the intercom/radio.
This works very well and way cheaper than the CEP set up.
The only other thing I might change is to find a 90 degree adapter so the plug doesn't stick out so far from the helmet, not really a problem in my airplane.
I may have forgotten something, feel free to ask questions, suggestions welcome as well.
Hope this helps. 37 years in aviation I've lost enough of my hearing.
